Over the years, a large variety of fiber optic connectors have been designed for most fiber optic installations. Lightwave equipment manufacturers have never standardized on any one connector type, they actually provide a selection of connectors for their equipment interface.
It is very important to choose the fiber connector type for your applications. You should maintain a connector standard throughout a fiber optic project.
:: The components of a fiber connector
For most fiber optic connectors, the major components are ferrule, connector body, connector cap and strain relief boot.
Ferrule
The ferrule is the center part of the connector. It contains the optical fiber in a center hole. Ferrule can be made from ceramic (Zirconia), stainless steel or composite material.
Ceramic ferrule is the most popular material since it has stable temperature characteristics. The most common ceramic is Zirconia which is a white hard ceramic material. Ceramic ferrule is used for both single mode and multimode connectors. It offers the lowest insertion loss and the best repeatability.
Connector Body
Fiber optic connector body can be steel or plastic. The body design differs from connector to connector. The connector body provides the mechanism to hold the ferrule and other parts together. It also provides the locking mechanism for connector mating. The most common locking mechanisms are push pull, snap in, thread on and twist on.
Connector Cap
Connector cap often has the same material as the body: either steel or plastic. The cap can be screw on, twist lock or snap on for connector mating.
Strain relief Boot
Strain relief boot is the part connecting the connector body and the fiber cable. It is often made from rubber. Although it looks minimal, it is actually one of the most critical parts in a connector. It provides strain relief on the optical fiber to prevent micro bending, breakage and provides mechanical support for fiber and connector handling.
:: Legacy Fiber Connector Types
The following list shows the legacy connector types that have been deployed in numerous fiber optic networks for many years.
ST Connector
ST connector was once the most popular fiber connector. It was well liked for both single mode and multimode fiber connections. The average insertion loss for a ST connector is about 0.5dB.
ST connector has a twist on locking mechanism which is not susceptible to loosening in vibrating environment. It is most often used in LAN networks.
FC Connector
FC connector is popular for single mode applications. It has the lowest insertion loss and the best repeatability. It has a thread on locking mechanism.
SMA connector
SMA connector is a pretty old connector type which is mostly used for multimode applications. Today it is still being using on medical equipment.
There are two types of SMA connectors on the market: SMA 905 and SMA 906. The only difference between them is that SMA 906 has a straight ferrule while SMA 905 has a step down ferrule.
D4 Connector
The NEC D4 was probably the first connector to use ceramic or hybrid ceramic/stainless steel ferrules. It uses a smaller ferrule than SCs or FCs. It was widely used in telco networks in the 80s to early 90s and some may still be in use.
FDDI connector
Besides the SC Duplex, you may occasionally see the FDDI duplex connectors which mate to their specific networks. They are generally used to connect to the equipment from a wall outlet, but the rest of the network will have ST or SC connectors. Since they both use 2.5 mm ferrules, they can be mated to SC or ST connectors with adapters.
Biconic Connector
Biconic connector’s yellow body indicating a SM version mutlimode versions were usually black. Biconic connector was developed by a team led by Jack Cook at Bell Labs in Murray Hill, NJ.
Author Resource:-
Colin Yao is an expert on fiber optic networking technologies and products. Learn even more about bulk single mode fiber, corning fiber optic cable, outdoor single mode fiber on Fiber Optics For Sale Co. web site http://www.fiberoptics4sale.com/page/FOFS/CTGY/Fiber_Optic_Cables_Fibers
The Free Ride In Public Schools 27 Nov 2008 at 11:28am
Why should public-school students bother doing homework or studying hard if they advance to the next grade no matter how bad they do in class? That would be dumb, and these kids are not dumb. Punishing the Victim -- Why Public Schools Pressure Parents To Give Their Kid... 27 Nov 2008 at 11:28am
It is normal for bright, energetic kids to be bored in public school. To solve the problem of "unruly" children, public schools now pressure parents to give their kids potentially dangerous mind-altering drugs. The Graceful Art of Defrazzling - For Mothers 27 Nov 2008 at 11:28am
An introduction to a "defrazzled" method of surviving life as a mother
If you are interested in learning about and discussing social services and social services agency management, please visit SocialServicesAgencyManagement.com where you will also learn about the new ecological model of excellence.
![[Valid RSS feed]](http://www.SooooSmart.com/images/icon_Rss.png "XML Feed For RSS"){kind=icon}
Category Rss Feed
Print This Article
Add To Favorites
